![]() ![]() The folks at Flux told us we wouldn’t like it very much. It’s nearly impossible to disengage with the firing hand. Our decision to retain the manual safety was the wrong one. The first Flux Defense MP17 model shipped with a holster, with Flux Defense eyeing law enforcement and military units as potential customers Flux has yet to finish something similar for the Raider, but it’s an ongoing effort and may well be available by the time you read these words. We’re hoping to see a left or ambidextrous design with the next generation. Some actions can be clumsily performed by a lefty, but it’s not an experience you’ll enjoy very much. All controls and manipulations of the Raider are designed and intended to be used by right-handers. If you’re a lefty, take a pass on this one - at least for now. See the sidebar for more information on this suppressor.Īnd spray paint. While you can play around with configuration, we kept this one short for transport. Until that time, we’re just grabbing the front of the serrated Grey Ghost Precision slide for nearly all of our manipulations.įor a silencer (because of course we have a silencer), we rolled with the modular, user serviceable Banish 45 from Silencer Central. However, by the time of publishing, there may be more than one viable charging handle available. We received a preproduction charging handle from another company that fits into the front sight dovetail - but broke it almost immediately (thus the nature of preproduction parts). Without an extended slide stop lever or a forward charging handle, it can be kind of a pain to lock the slide back on the Raider. Allow the primary magazine to drop while you swap in the secondary. Using the thumb of your support hand, press the button in far enough to remove both magazines. No one will be hurting for a lack of options, but we suggest you find the one you like and just stick to it.įor changing magazines in a flash, this was our preferred method: wrap the fingers of your support hand around the spare mag holder. A push-button on the right, a thumb release along the bottom, and a sliding mechanism on the left. I hope this helps, if you have anymore questions let me know.There are three ways to release magazines with the Raider. Plus I'll say it again, I'm a sucker for spring loaded gizmos. This Flux Brace package is exactly what I wanted. ![]() It turns the glock pistol into a very usable, compact PDW (that is still very easy to use as a pistol.) I too was very interested in the P320, and I too thought the Roni was too bulky. I personally think it is a great invention. There are a lot of good and snobby "mall ninja" negative comments about this brace. I think these would work fine, looking where the rails sit and the clearance from the receiver I see no issueģ) Do you find the brace helps you manage recoil and get back on target faster?Ĥ) any other pro/cons you have that haven't been asked? Thanks! ![]() But the spring pressure does push the rails past the lock, so I usually have to give the rear of the brace a "smack" to lock it downĢ) Can you use extended slide stop levers? Yes, the brace locks up solid when deployed. I'll be shooting it soon enough and will report back on that as Does the brace lock once it's deployed? Sorry I do not, I have this brace on a bone stock Gen4 G17.Īny other questions let me know. Do you have a polymer80 frame by chance to see how much work would need to be done to fit? They are flush with the front end of the gun though.Ħ. The rods stick out about a bit from side-to side, but they do not wiggle they stay put. When in closed position, do the front ends of the brace arms want to wiggle and stick out? Molds into the gun, not uncomfortable at all.ĥ. The curve/angle where the mount meats the grip is a natural feel. Does it feel odd at all? Uncomfortable for the new angle of your trigger finger? It looks like the "mount" takes up some vertical space of the grip for your hand. Length from trigger face to ass end is 12.5"Ĥ. What is the length from face of trigger to ass end of brace? The mount does not move or wiggle at all, very solidģ. Yes, 1 pin but the engineering tolerances on this are awesome. Does it seem like the 1 pin that is holding it in place is doing its job? Solid, etc? I have standard height sights on my G17 and they are perfect, no need for suppressor height sightsĢ.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |